You're here :
ASI Recessed Baby Changing Station Door, Flange & Cabinet - 34 1/4" W x 22 3/4" H x 3 3/4" D
Item #: ASI 9013 By ( American Specialty INC )
Item #: ASI 9013 By ( American Specialty INC )
ASI 9013 | ASI Recessed Baby Changing Station Door, Flange & Cabinet
American Specialty Recessed Baby Changing Station Door, Flange & Cabinet: shall be type 304 stainless steel, all welded construction.
- All exposed surfaces shall be polished to a No 4 satin finish. The door shall be 16 gauge (1.6 mm) and the flange and cabinet shall be 18 gauge (1.3mm).
- The changing table shall be equipped with a rounded contoured pull handle and shall have a concealed damped gas spring to assist user in opening and closing unit with one hand.
- The bed liner shall be light gray, high impact plastic with a smooth finish for easy cleaning.
- The liner shall be shaped to cradle a child’s body and shall be equipped with a child protection safety strap and cam buckle adjustable with one hand.
- Unit shall include two bag hooks, a bed liner dispenser, and a C-fold towel and multi-fold towel dispenser that needs no adapters.
- Unit shall have a minimum holding capacity of 400 lbs. (181.4 kg).
- The strength of the supporting wall and hardware must be adequate to support the rated load.
- Unit shall provide graphic safety instructions in 4 languages.
- Unit shall comply with ASTM F-2285 and ANSI Z535 and shall be warranted for (5) years against defects in material or workmanship.
- Wall Opening: 34 1/4" W x 22 3/4" H x 3 3/4" D
Installation:
- Provide rough wall opening 34-1/4" (870mm) wide x 22-3/4" (578mm) high x 3-3/4" (95mm) minimum depth from face of finished wall.
- Mount unit in wall opening using either four (4) No 10 x 1-1/2" (38mm) long self-tapping screws through side holes or four (4) 3/8" x 2" (51mm) lag screws (or other fasteners appropriate for wall conditions) through mounting holes in rear wall of cabinet.
- Use washers and snap covers provided. For compliance with ADA Accessibility Guidelines, install unit so that top edge of changing table is 32" to 32-3/8"
(813mm to 822 mm) above finished floor (AFF).
Operation:
- Pull down changing table is counterbalanced with a damped gas spring and can be opened or closed with one hand by grasping pull handle.
- Secure the child in place by using child protection safety strap.
- The safety strap and cam buckle are assembled by sliding the safety strap into the cam buckle until it is snug on child.
- Tighten or loosen the strap by pulling the strap end through and clamping the buckle.
- To unbuckle the strap simply lift the buckle lever.
American Specialty Recessed Baby Changing Station Door, Flange & Cabinet: shall be type 304 stainless steel, all welded construction.
- All exposed surfaces shall be polished to a No 4 satin finish. The door shall be 16 gauge (1.6 mm) and the flange and cabinet shall be 18 gauge (1.3mm).
- The changing table shall be equipped with a rounded contoured pull handle and shall have a concealed damped gas spring to assist user in opening and closing unit with one hand.
- The bed liner shall be light gray, high impact plastic with a smooth finish for easy cleaning.
- The liner shall be shaped to cradle a child’s body and shall be equipped with a child protection safety strap and cam buckle adjustable with one hand.
- Unit shall include two bag hooks, a bed liner dispenser, and a C-fold towel and multi-fold towel dispenser that needs no adapters.
- Unit shall have a minimum holding capacity of 400 lbs. (181.4 kg).
- The strength of the supporting wall and hardware must be adequate to support the rated load.
- Unit shall provide graphic safety instructions in 4 languages.
- Unit shall comply with ASTM F-2285 and ANSI Z535 and shall be warranted for (5) years against defects in material or workmanship.
- Wall Opening: 34 1/4" W x 22 3/4" H x 3 3/4" D
Installation:
- Provide rough wall opening 34-1/4" (870mm) wide x 22-3/4" (578mm) high x 3-3/4" (95mm) minimum depth from face of finished wall.
- Mount unit in wall opening using either four (4) No 10 x 1-1/2" (38mm) long self-tapping screws through side holes or four (4) 3/8" x 2" (51mm) lag screws (or other fasteners appropriate for wall conditions) through mounting holes in rear wall of cabinet.
- Use washers and snap covers provided. For compliance with ADA Accessibility Guidelines, install unit so that top edge of changing table is 32" to 32-3/8"
(813mm to 822 mm) above finished floor (AFF).
Operation:
- Pull down changing table is counterbalanced with a damped gas spring and can be opened or closed with one hand by grasping pull handle.
- Secure the child in place by using child protection safety strap.
- The safety strap and cam buckle are assembled by sliding the safety strap into the cam buckle until it is snug on child.
- Tighten or loosen the strap by pulling the strap end through and clamping the buckle.
- To unbuckle the strap simply lift the buckle lever.
- Item Number: ASI 9013
- ASI Baby Changing Station- Recessed
- 34 1/4" W x 22 3/4" H x 3 3/4" D
- Free Shipping
Shipping Weight per Each : 35.00 lbs
NOTE: The product title and description supersedes the picture shown. The picture provided by the manufacturer is not always exact.
|
( See all Source One Plus products by American Specialty INC ) |